Clamping force / Test notes

    Air Vise vs. Manual Vise: Same Clamping Force, No Torque Wrench

    Compare the Air Vise 6" Table Vise with a manual vise using measured clamping force at 50, 70 and 100 PSI, plus torque-wrench results and practical FAQs.

    Clamping force testWatch on YouTube

    The American made Air Vise™ 6" Table Vise (AV-T-6) from Air Vise & Workholding delivers the same clamping force machinists already get from a torque wrench. At 70 PSI it matches a single station vise torqued to 17 ft-lbs, about 2,000 lbs. At 100 PSI it matches 27 ft-lbs, about 2,500 lbs. The difference is how you get there: the Air Vise is set once with shop air instead of by hand on every part, so the force is the same on part one and part 1,000.

    Clamping force is the number every machinist relies on and few actually measure. Too little and the part shifts under the cutter. Too much and thin walls distort or the part springs when you release it. A lot of you asked how Air Vise clamping force compares to a torque wrench, so in the video, Austin puts a clamping force gauge in both vises to see exactly what each one delivers.

    70 PSI Air Vise17 ft-lbsManual vise · About 2,000 lbs
    100 PSI Air Vise27 ft-lbsManual vise · About 2,500 lbs

    If you clamp in the 17 to 27 ft-lb range today, you don't give up any holding power by switching to air. You just stop reaching for the wrench.

    How the test was run

    1. Air Vise 6" Table Vise

      Set the air regulator to 50, 70 and 100 PSI and read the gauge at each pressure.

    2. Traditional single station vise

      Tightened the handle with a torque wrench to 17, 27 and 36.5 ft-lbs and read the gauge at each torque.

    3. Same gauge, same setup

      Readings are rounded to what the gauge showed on camera.

    Clamping force test results

    Gauge readings at each air pressure and torque setting.
    ViseSettingClamping force
    Air Vise 6" Table Vise50 PSIAbout 1,200 lbs
    Air Vise 6" Table Vise70 PSIJust under 2,000 lbs
    Air Vise 6" Table Vise100 PSIAbout 2,500 lbs
    Single station vise17 ft-lbsJust under 2,000 lbs
    Single station vise27 ft-lbsJust over 2,500 lbs
    Single station vise36.5 ft-lbsAbout 3,000 lbs

    The single station vise reached the highest number in the test, about 3,000 lbs. But that number only holds when someone uses a torque wrench on every part. The Air Vise holds its number on every cycle.

    What repeatable clamping changes

    Same force, part one to part 1,000

    Force is set once at the regulator. Every part in the run is clamped the same way, no matter who loads it.

    No operator variation

    Without a torque wrench, "tight" means something different to every machinist, and to the same machinist at the end of a long shift.

    Part protection

    Thin walls and finished surfaces need less force. Turning down a regulator is faster and more exact than backing off a handle by feel.

    Automation ready

    An Air Vise opens and closes with air, so a robot, cobot or M-code can run it. A handle cannot.

    Clamping force questions

    How much clamping force does an Air Vise have?

    In our test, the Air Vise 6" Table Vise held about 1,200 lbs at 50 PSI, just under 2,000 lbs at 70 PSI and about 2,500 lbs at 100 PSI. Force goes up as you raise the air pressure.

    What PSI equals my torque wrench setting?

    In our test, 70 PSI on the Air Vise matched 17 ft-lbs on a single station vise (about 2,000 lbs), and 100 PSI matched 27 ft-lbs (about 2,500 lbs).

    Is an Air Vise as strong as a manual vise?

    Across the 17 to 27 ft-lb range, yes. The manual vise went higher, about 3,000 lbs at 36.5 ft-lbs, but only when torqued with a wrench. The Air Vise delivers the same force on every cycle.

    How do I convert vise torque to clamping force?

    It depends on each vise's screw and mechanism, so measure with a clamping force gauge or use the maker's chart. In our test, 17, 27 and 36.5 ft-lbs produced about 2,000, 2,500 and 3,000 lbs.

    How do I set clamping force on an Air Vise?

    Adjust the air regulator. Higher pressure means more force, and the setting stays the same for every part until you change it.

    See every gauge reading in the video, and learn more about the Air Vise 6" Table Vise at airvise.com.

    Air Vise 6" Table Vise

    Set the force once. Keep it consistent on every cycle.

    View the vise

    Consistent clamping is just one piece of the puzzle. Explore the full lineup of trusted brands at Workholding Solved, including TE-CO, TOOLEX, Raptor Workholding and Mitee-Bite.